Fujitsu M5000 Manual de usuario Pagina 168
- Pagina / 310
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
10-4 SPARC Enterprise M4000/M5000 Servers Service Manual • December 2010
10.1.1 Accessing the 60-mm Fan Module
1. From the XSCF Shell prompt, use the replacefru command to disable the fan
to be removed.
The replacefru command is menu-driven. replacefru will continue while the
fan is removed and then test the fan. Refer to Section 4.3.1, “Removing and Replacing
a FRU” on page 4-7 for more information.
Caution – To prevent the equipment rack from tipping over, you must deploy the
antitilt feature, if applicable, before you slide the server out of the equipment rack.
Caution – When drawing out the M4000/M5000 server to the front, release the cable
tie holding the PCI cables on the rear of the server.
2. Deploy the rack’s antitilt features (if applicable) and slide the server out of the
equipment rack.
See Section 5.1.1, “Sliding the Server Out of the Equipment Rack” on page 5-2.
Caution – Use proper ESD grounding techniques when handling components. See
Section 1.1, “Safety Precautions” on page 1-1.
XSCF> replacefru
- Service Manual 1
- Contents 5
- Contents vii 7
- Contents ix 9
- Contents xi 11
- Contents xiii 13
- Contents xv 15
- G. Abbreviations G–1 16
- Index Index–1 16
- SPARC Enterprise M4000/M5000 18
- Servers Documentation 18
- Text Conventions 19
- Notes on Safety 20
- Documentation Feedback 20
- Safety and Tools 21
- 1.2 System Precautions 22
- 1.2.4 Handling Components 23
- Fault Isolation 25
- Diagnostic Method Flow Chart 26
- Chapter 2 Fault Isolation 2-3 27
- Configuration 28
- XSCF> showhardconf 29
- # showrev 31
- XSCF> version(8) 31
- 2.3 Operator Panel 32
- M4000 Server Operator Panel 33
- M5000 Server Operator Panel 34
- TABLE 2-3 35
- TABLE 2-4 36
- Switches (Operator Panel) 37
- 2.4 Error Conditions 38
- ■ Diagnoses the problems 39
- Output Displayed Description 40
- 2.4.2 Monitoring Output 41
- 2.4.3 Messaging Output 41
- 2.5 LED Functions 42
- Component LED Descriptions 43
- 2.6.2.1 fmdump -V Command 46
- 2.6.2.2 fmdump -e Command 47
- 2.6.3.1 fmadm repair Command 47
- 2.6.3.2 fmadm config Command 48
- Commands 49
- 2.7.1.1 Options 50
- 2.7.2.1 Options 51
- 2.7.3.1 Options 54
- The prtconf output continued 55
- 2.7.4.1 Options 57
- 2.7.5 Using the ping Command 58
- 2.7.6 Using the ps Command 59
- 2.7.7.1 Options 60
- 2.8 Other Issues 61
- Periodic Maintenance 63
- FRU Replacement Preparation 65
- FRU Replacement Information 66
- TABLE 4-1 67
- 4.2 Active Replacement 68
- 4.3 Hot Replacement 70
- EXAMPLE 4-3 showhardconf 73
- EXAMPLE 4-4 showhardconf 74
- TABLE 2-11 for LED status 75
- Off and On) 76
- EXAMPLE 4-6 showhardconf 79
- (domain console) again: 80
- EXAMPLE 4-8 show-devs 81
- EXAMPLE 4-9 probe-scsi-all 82
- Internal Components Access 83
- FIGURE 5-1) 84
- FIGURE 5-2) 86
- 5.2.1 Removing the Top Cover 87
- FIGURE 5-1). The 88
- FIGURE 5-4) 88
- 5.2.2 Replacing the Top Cover 90
- 5.3.1 Removing the Fan Cover 90
- 5.3.2 Replacing the Fan Cover 92
- Storage Devices Replacement 93
- 2 Hard disk drive (HDD#1) 94
- 3 Hard disk drive (HDD#0) 94
- Removing the Hard Disk Drive 96
- 6.1.4 Securing the Server 97
- M4000 Server 98
- 6.1.8 Securing the Server 100
- M5000 Server 101
- 6.1.12 Securing the Server 103
- Replacement 104
- Location Number Component 105
- Figure Leg end 107
- ● Power off the server 108
- FIGURE 6-7) 108
- 6.2.5 Securing the Server 109
- 6.2.9 Securing the Server 111
- 6.2.13 Securing the Server 114
- (TAPEBP) on the M4000 server 116
- (TAPEBP) on the M5000 117
- Removing the Tape Drive 118
- 6.3.4 Securing the Server 119
- 6.3.8 Securing the Server 122
- 6.3.12 Securing the Server 125
- Power Systems Replacement 127
- Power Supply Unit Locations 128
- XSCF> replacefru 130
- 7.1.4 Securing the Server 131
- I/O Unit Replacement 133
- 1 I/O unit (IOU#0) 134
- 1 I/O unit (IOU#1) 135
- 2 I/O unit (IOU#0) 135
- 8.1 PCI Cassette Replacement 136
- FIGURE 8-3 137
- FIGURE 8-4) 137
- Removing the PCI Cassette 138
- 8.2 PCI Card Replacement 139
- 8.2.2 Installing the PCI Card 140
- 1-2-3 sequence in FIGURE 8-6 141
- 8.3 I/O Unit Replacement 142
- 8.3.3 Installing the I/O Unit 143
- 8.3.4 Securing the Server 144
- 2 DC-DC Converter Connector 145
- 3 DC-DC Converter (DDC_B#0) 145
- 4 DC-DC Converter (DDC_A#0) 145
- (DDC_A#0 or DDC_B#0) 146
- (DDC_A #0 or DDC_B #0) 146
- FIGURE 8-9) 147
- FIGURE 8-10) 148
- #0 or DDC_B #0) 149
- FIGURE 8-13) 150
- FIGURE 8-12) 150
- 8.4.4 Securing the Server 153
- FIGURE 8-14) 154
- 8.4.8 Securing the Server 156
- XSCF Unit Replacement 159
- M4000 server 160
- 9.1.1 Accessing the XSCF Unit 161
- 9.1.2 Removing the XSCF Unit 162
- 9.1.4 Securing the Server 163
- 3. Reset the clock 164
- Fan Modules Replacement 165
- 1 172-mm fan module (FAN_A#1) 167
- 2 172-mm fan module (FAN_A#0) 167
- 3 172-mm fan module (FAN_A#3) 167
- 4 172-mm fan module (FAN_A#2) 167
- 60-mm Fan Module Removal 169
- 10.1.4 Securing the Server 170
- 172-mm Fan Module Removal 172
- 10.1.8 Securing the Server 173
- FIGURE 10-5 #1) 175
- FIGURE 10-5 #2) 175
- FIGURE 10-5 #3 and #4) 175
- 10.1.12 Securing the Server 176
- Fan Backplane 177
- Backplane 180
- 10.1.16 Securing the Server 180
- 10.1.20 Securing the Server 184
- Memory Board Replacement 185
- 1 Memory board (MEMB#0) 186
- 2 Memory board (MEMB#1) 186
- 3 Memory board (MEMB#2) 186
- 4 Memory board (MEMB#3) 186
- Memory Board Removal 189
- 11.1.4 Securing the Server 190
- 11.2 DIMM Replacement 191
- EXAMPLE 11-1 showhardconf 192
- FIGURE 11-4) 193
- 11.2.3 Installing Memory: 194
- 11.2.4 Accessing the DIMMs 194
- 11.2.5 Removing the DIMMs 195
- 11.2.6 Installing the DIMMs 196
- 11.2.7 Securing the Server 196
- CPU Module Replacement 197
- 1 CPU module (CPUM#1) 198
- 2 CPU module (CPUM#0) 198
- 2 CPU module (CPUM#1) 199
- 3 CPU module (CPUM#2) 199
- 4 CPU module (CPUM#3) 199
- 1 CPU module (CPUM#0) 199
- CPU Module Removal 201
- 12.1.4 Securing the Server 202
- 12.2 CPU Upgrade 203
- Added to a New Domain 204
- ■ Set up the domain 205
- XSCF> poweron -d domain_id 206
- XSCF> showlogs power 206
- XSCF> showlogs error -v 206
- XSCF> showstatus 206
- XSCF> poweroff -a 207
- XSCF> poweron -a 208
- XSCF> version -c cmu -v 208
- SPARC64 VI 209
- ■ Set up XSB 210
- ■ Set up the LSB 210
- ■ Add the XSB to the domain 210
- Motherboard Unit Replacement 213
- FIGURE 13-3) 217
- 13.1.4 Securing the Server 218
- FIGURE 13-4) 220
- 13.1.8 Securing the Server 223
- 2 DC-DC Converter (DDC_A#0) 224
- 3 DC-DC Converter (DDC_A#1) 224
- Removing the DC-DC Converter 227
- 13.2.4 Securing the Server 228
- 13.2.8 Securing the Server 230
- 13.3 Motherboard Unit Upgrade 231
- Backplane Unit Replacement 235
- FIGURE 14-3) 240
- 14.1.4 Securing the Server 242
- FIGURE 14-4) 244
- 14.1.8 Securing the Server 246
- Operator Panel Replacement 249
- 1 Operator panel 250
- FIGURE 15-3) 253
- Removing the Operator Panel 254
- 15.2.3 Securing the Server 255
- Components List 257
- Location 258
- Number Component 258
- B.1 Server Configuration 263
- System Features 264
- System Features (Continued) 265
- FRU List 267
- FRU Components 268
- C.2 System Boards 269
- C.2.2 CPU Module 270
- C.2.3 Memory Board 271
- C.3 Backplane Unit 272
- C.4 I/O Unit 272
- C.5 Power 273
- C.6 FAN Module 274
- 2 60-mm fans (1+ 1 redundant) 275
- C.8 Drives 276
- C.8.3 Tape Drive Unit (TAPEU) 277
- TABLE C-11) 278
- TABLE C-10) 278
- APPENDIX 279
- D.1 Serial Port 280
- D.2 UPC (UPS Control) Port 281
- D.3 USB Port 281
- UPS Controller 283
- E.3 Signal Line Configuration 284
- E.4 Power Supply Conditions 285
- E.5 UPS Cable 286
- E.6 UPC Connector 287
- Air Filters 289
- XSCF> showaltitude 290
- 1000m 290
- Filter is installed 290
- XSCF> showaltitude 291
- Hook and Loop Tape Locations 292
- Appendix F Air Filters F-5 293
- Appendix F Air Filters F-7 295
- FIGURE F-6) 296
- Appendix F Air Filters F-9 297
- Appendix F Air Filters F-11 299
- Appendix F Air Filters F-13 301
- FIGURE F-12) 301
- FIGURE F-4 or FIGURE F-9 and 302
- FIGURE F-10 302
- Appendix F Air Filters F-15 303
- Abbreviations 305
- TABLE G-1 (Continued)Acronyms 306
- Abbreviation Full name 306
- Appendix G Abbreviations G-3 307
Relacionado con productos y manuales para Ordenadores Fujitsu M5000
(126 paginas)
(289 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales