Fujitsu MAP3147 Manual de usuario

C141-E167-01ENMAP3367, MAP3735, MAP3147 NP/NC SERIESMAS3367, MAS3735 NP/NC SERIESDISK DRIVESSCSI LOGICAL INTERFACE SPECIFICATIONS

This page is intentionally left blank.

Command Specifications3 - 38 C141-E167Together with the RELEASE command, this command controls exclusive access to the logical unit(IDD) under a multi

3.1 Control/Sense CommandsC141-E167 3 - 39(3) Changing the reserve conditions (Superseding Reserve)The INIT which has the reserve right for an IDD (t

Command Specifications3 - 40 C141-E167• INIT #A can issue INQUIRY, REQUEST SENSE, RELEASE and RESERVE commandsto TARG #0, but other commands are reje

3.1 Control/Sense CommandsC141-E167 3 - 413.1.13 RELEASE (17) BitByte765432100 X‘17’1 LUN 3rd Pty 3rd Pty Dev ID 02×××××××

Command Specifications3 - 42 C141-E1673.1.14 RELEASE EXTENDED (57) BitByte765432100 X‘57’1 LUN 3rd Pty 0 0 0 02××××××××3 T

3.1 Control/Sense CommandsC141-E167 3 - 43The length of the sense data in the IDD is 48 bytes. The "Transfer byte length" field in the CDB

Command Specifications3 - 44 C141-E167• Sense data cannot be sent due to a hardware error in the IDD• An unrecoverable error is detected on the SCSI

3.1 Control/Sense CommandsC141-E167 3 - 45Value Description00b Current threshold values01b Current cumulative values10b Default threshold values11b D

Command Specifications3 - 46 C141-E167(1) Page codeThis field indentifies which log page is being transferred.The log pages that can be transferred by

3.1 Control/Sense CommandsC141-E167 3 - 47(1) Paramter codeThis field identifies the log paramter being transferred for that log page.(2) Byte 2a) DU

C141-E167 viiContentsCHAPTER 1 Command Processing...

Command Specifications3 - 48 C141-E167(4) Parameter valueThis field indicates actual "threshold value" or "cumulative value". The

3.1 Control/Sense CommandsC141-E167 3 - 49Page Code Description Parameter Pointer00 Supported Log Pages Ignored01 Buffer Overrun / Underrun Page Supp

Command Specifications3 - 50 C141-E167The PERSISTENT RESERVE IN command obtains information about the reservation requirementsand reservation keys tha

3.1 Control/Sense CommandsC141-E167 3 - 513.1.18.1.2 READ RESERVATIONSIn the READ RESERVATION service action, the drive transfers the following info

Command Specifications3 - 52 C141-E167This counter value is not incremented in the following cases:When the PERSISTENT RESERVE IN command is executedW

3.1 Control/Sense CommandsC141-E167 3 - 53The "Additional Length" field contains a count of the number of bytes to follow in the "Reser

Command Specifications3 - 54 C141-E167Code Name Description0h Logical Unit Persistent reservation applies to an entire logical unit1h Reserved Reserve

3.1 Control/Sense CommandsC141-E167 3 - 55Table 3.2 Persistent reservation type codesCode Name Description0h ReservedReads Shared: Any initiator can

Command Specifications3 - 56 C141-E1673.1.19 PERSISTENT RESERVE OUT (5E) BitByte765432100X'5E'1 0 0 0 Service Action2 Scope Type30

3.1 Control/Sense CommandsC141-E167 3 - 57The RESERVE, PREEMPT, and PREEMPT AND ABORT service actions of this commanddetermine whether any conflict o

Contentsviii C141-E167CHAPTER 2 Data Buffer Management ...

Command Specifications3 - 58 C141-E167Table 3.3 PERSISTENT RESERVE OUT command service action codesCode Name Description00h REGISTER Registers a rese

3.1 Control/Sense CommandsC141-E167 3 - 59For the "Reservation Key" field, an 8-byte key code provided by the application client is set in

Command Specifications3 - 60 C141-E167Table 3.4 PERSISTENT RESERVE OUT service actions and valid parametersParametersService Action Allowed Scope type

3.1 Control/Sense CommandsC141-E167 3 - 61This command requests that the peripheral device logical unit inventory be sent to the applicationclient.Thi

Command Specifications3 - 62 C141-E1673.1.21 REPORT DEVICE IDENTIFIER (A3) BitByte765432100X'A3'1 0 0 0 Service Action (X’ 05’)200

3.1 Control/Sense CommandsC141-E167 3 - 63The "Identifier Length" field specifies the length in bytes of the "Identifier" field.I

Command Specifications3 - 64 C141-E167The "Allocation Length" field specifies the length in bytes of the Identifier that shall be transferre

3.2 Data Access CommandsC141-E1673 - 653.2 Data Access Commands3.2.1 READ (08) BitByte765432100 X‘08’1 LUN Logical Block Address (MSB)2 Logic

Command Specifications3 - 66C141-E1673.2.2 READ EXTENDED (28) BitByte765432100 X‘28’1LUN×FUA 0 0 02 Logical Block Address (MSB)

3.2 Data Access CommandsC141-E1673 - 673.2.3 WRITE (0A) BitByte765432100X‘0A’1 LUN Logical Block Address (MSB)2 Logical Block

ContentsC141-E167 ix3.1.19 PERSISTENT RESERVE OUT (5E) ...3-563.1.19.1

Command Specifications3 - 68C141-E167Note:Even when there is an error in the specification in the CDB, or when a write operation to the diskmedia cann

3.2 Data Access CommandsC141-E1673 - 69When this bit is "1", it indicated that the IDD shall access the media in performing the commandprio

Command Specifications3 - 70C141-E167processing is not prohibited, even if a correctable data check is detected during the verify check, it isregarded

3.2 Data Access CommandsC141-E1673 - 713.2.7 SEEK (0B) BitByte765432100X‘0B’1 LUN Logical Block Address (MSB)2 Logical Block

Command Specifications3 - 72C141-E167This command executes a seek operation of the cylinder/track where the logical data block specifiedin the "L

3.2 Data Access CommandsC141-E1673 - 73Also, the size of the range where access is permitted, specified in this command in the "Block count"

Command Specifications3 - 74C141-E167Notes:1. Commands which come under restrictions in read operations or write operations when "1"is speci

3.3 Format CommandsC141-E1673 - 75The values specified in the "Logical block address" field and "Block count" field in the CDB are

Command Specifications3 - 76C141-E167(1) Defect listIn order to register or specify the positions of defects on the disk media in connection with defe

3.3 Format CommandsC141-E1673 - 77(2) Specifying the initialization methodThe INIT can specify the method of defect processing executed by this comma

Contentsx C141-E1674.1.6 Caching parameters (page code = 8)... 4-214.

Command Specifications3 - 78C141-E167(3) Format parametersFigure 3.13 shows the data format of the Format parameter transferred from the INIT when “1”

3.3 Format CommandsC141-E1673 - 79a. HeaderThe top of the format parameter transferred from the INIT is a 4-byte header. The INIT canspecify the met

Command Specifications3 - 80C141-E167• Immed (Immediate)“1” : If “1” is specified in the Immed (immediate) bit, at the point when the CDB’slegality i

3.3 Format CommandsC141-E1673 - 81Note:In order to specify an entire track as defective, X ‘FFFFFFFF’ must be specified as thebyte distance from the

Command Specifications3 - 82C141-E167 BitByte765432100 Cylinder No. (MSB)1 Cylinder No.2 Cylinder No. (LSB)3 Head No.4 Physi

3.3 Format CommandsC141-E1673 - 83boundaries (User Space), and is recorded as the G List, but formatting processing isexecuted only for the User Spac

Command Specifications3 - 84C141-E167Table 3.5 FORMAT UNIT command defect processing (2 of 3)CDB Byte 1 Header FmtData CmpLst Defect listformat FOV DP

3.3 Format CommandsC141-E1673 - 85Table 3.5 FORMAT UNIT command defect processing (3 of 3)Note 1) ddd: 0,0,0= D List in the block address format.1,0,

Command Specifications3 - 86C141-E167Note:Copying of the contents of data in the logical data blocks specified in the “Defect data” list toalternate b

3.3 Format CommandsC141-E1673 - 87The logical block address of defective data blocks is described in 4-byte format in the defectdescriptor. When mul

ContentsC141-E167 xi4.2.8.4 Start-stop cycle counter (Page 0E, Code 0004)...4-544.2.9 Applic

Command Specifications3 - 88C141-E1671. Delete the defect descriptors which precede the defect descriptor that specifies the logical blockaddress disp

3.3 Format CommandsC141-E1673 - 89PList GList Defect Data Type1 1 P List and G List1 0 P List only0 1 G List only0 0 4-byte header information only (

Command Specifications3 - 90C141-E167b. G List (grown list) bitWhen this bit is “1,” it indicates that G List defect data are included in the defect d

3.3 Format CommandsC141-E1673 - 91• Defect List Length field: The total number of bytes described in the “Defect ListFormat” specifying defect data i

Command Specifications3 - 92C141-E167• When data are in the “Byte Distance from the Index Format,” when the P List isreported, multiple defect positi

3.4 Maintenance, Diagnostic CommandsC141-E1673 - 93Type of Self-diagnosis Test UnotOfl = “0” UnitOfl = “1”1) Controller Function Test××2) Disk Drive

Command Specifications3 - 94C141-E167Note:When “1” is specified in the “SelfTest (self test)” bit in this command, the command executionresults are re

3.4 Maintenance, Diagnostic CommandsC141-E1673 - 953. When a command other than the RECEIVE DIAGNOSTIC RESULTS command is linked tothis command, the

Command Specifications3 - 96C141-E167This parameter page specifies transfer of the “Page code” list of the parameter page supported bythe IDD in the S

3.4 Maintenance, Diagnostic CommandsC141-E1673 - 97The “Address Format Before Conversion” field shows the format of the address informationspecified

Contentsxii C141-E167IllustrationsFigures1.1 6-Byte CDB Basic Format ...

Command Specifications3 - 98C141-E167SELF-TEST Code Description0,0,0 Refer to clause (2), Parameter Specification.0,0,1 The device server shall start

3.4 Maintenance, Diagnostic CommandsC141-E1673 - 99Notes:Exercise caution in the following points when using this command.1. In order to avoid damage

Command Specifications3 - 100C141-E167• Page parameter lengthThis field shows the byte length of the page parameter after byte 4.• Page parameterDat

3.4 Maintenance, Diagnostic CommandsC141-E1673 - 101 BitByte765432100 X ‘40’ (Page Code)1000000002 X ‘00’ (Page Parameter Length)3 X ‘0A’ (Pa

Command Specifications3 - 102C141-E167The description of address information shown in bytes 6 to 13 is the same as the descriptionspecifications in th

3.4 Maintenance, Diagnostic CommandsC141-E1673 - 103“Mode Bit” 3 2 1 0 Transfer Mode0 0 0 0 Header + Data, without Address Specification0 0 0 1 Heade

Command Specifications3 - 104C141-E167(2) Mode = 0, 0, 0, 1: Header + data, without address specificationThe format of data transferred from the INIT

3.4 Maintenance, Diagnostic CommandsC141-E1673 - 105Note:Depending on the setting in the IDD, if done using the START/STOP command, it is necessary t

Command Specifications3 - 106C141-E167The "Transfer Byte Length" field specifies the maximum number of bytes that shall be present in theDat

3.4 Maintenance, Diagnostic CommandsC141-E1673 - 1073.4.4 READ BUFFER (3C) BitByte765432100X‘3C’1 LUN 0 Mode2 X‘00’ (Buffer I

ContentsC141-E167 xiii4.1 MODE SELECT parameters: read/write error recovery parameters ...4-24.2 MODE SELECT

Command Specifications3 - 108C141-E167The “Transfer byte count” field in the CDB specifies the total number of bytes of the header andbuffer data whic

3.4 Maintenance, Diagnostic CommandsC141-E1673 - 109The “Transfer byte length” field in the CDB specifies the total number of bytes of header and buf

Command Specifications3 - 110C141-E167The "Addressing boundary" field in the buffer descriptor indicates the addressing boundary in thedata

3.4 Maintenance, Diagnostic CommandsC141-E1673 - 1113.4.5 READ LONG (3E) BitByte765432100X‘3E’1LUN000CORRCT02 Logical Block A

Command Specifications3 - 112C141-E167Error recovery processing during execution of this command is in accordance with the specificationsin (Page code

3.4 Maintenance, Diagnostic CommandsC141-E1673 - 113• Sense Key : 05 = ILLEGAL REQUEST• Sense Code/Sub-sense Code : 24-00 = Invalid field in CDB•

Command Specifications3 - 114C141-E167The IDD is not supported a "PBdata" bit. Therefore, if "PBdata" bit is one, this command ist

C141-E167 4 - 1CHAPTER 4 Parameter Data Formats4.1 Mode Parameters4.2 Log ParametersThis chapter describes detailed parameter data formats provided b

Parameter Data Formats4 - 2 C141-E167 BitByte765432100 000000011 X‘0A’ or X‘06’ (Page Length)2AWREARRETBRCERRPERDTEDCRDefault11101000

4.1 Mode ParametersC141-E167 4 - 3• READ • WRITE• READ EXTENDED • WRITE AND VERIFY (Write operation)• READ LONG • WRITE EXTENDED• SEND DIAGNOSTIC (Wr

This page is intentionally left blank.

Parameter Data Formats4 - 4 C141-E167f. PER (post error)"1" : When several errors (errors related to the disk drive), which were recovered

4.1 Mode ParametersC141-E167 4 - 5j. Correctable bit lengthThis parameter indicates the burst error length (bit length) which it is possible to apply

Parameter Data Formats4 - 6 C141-E167n. Recovery time limitThis parameter specifies the maximum time that can be used by the TARG for error recoverypr

4.1 Mode ParametersC141-E167 4 - 7Table 4.1 Combinations of error recovery flags (1 of 3)EER PER DTE DCR Error Recovery Procedure00001.Rereading is t

Parameter Data Formats4 - 8 C141-E167Table 4.1 Combinations of error recovery flags (2 of 3)EER PER DTE DCR Error Recovery Procedure01101.Rereading is

4.1 Mode ParametersC141-E167 4 - 9Table 4.1 Combinations of error recovery flags (3 of 3)EER PER DTE DCR Error Recovery Procedure11001.When a correct

Parameter Data Formats4 - 10 C141-E1674.1.2 Disconnect/reconnect parameters (page code = 2)The format of the page descriptor in this MODE SELECT param

4.1 Mode ParametersC141-E167 4 - 11Note:If transfer of this page descriptor is required by the MODE SENSE or MODE SENSE EXTENDEDcommand, the IDD repo

Parameter Data Formats4 - 12 C141-E167Note:If the value specified for the "buffer full ratio" or the "buffer empty ratio" is not w

4.1 Mode ParametersC141-E167 4 - 1300b= Perform disconnection according to the instructions of other parameters withoutusing DTDC.01b= When a data tr

C141-E167 1 - 1CHAPTER 1 Command Processing1.1 Command Format1.2 Status Byte1.3 Outline of Command Processing1.4 Command Queuing Function1.5 UNIT ATTE

Parameter Data Formats4 - 14 C141-E1674.1.3 Format parameter (page code = 3)The Page descriptor format of this MODE SELECT parameter is shown in Figur

4.1 Mode ParametersC141-E167 4 - 15a. Parameters for specifying alternate processing areas for defective blocks (bytes 2 to 9)The following 4 paramet

Parameter Data Formats4 - 16 C141-E167c. Parameters specifying sector format (bytes 12 to 19)• Data byte length/physical sectorsThis parameter specif

4.1 Mode ParametersC141-E167 4 - 17• HSEC (hard sectoring)When this bit is "1," it indicates that the data formatting method on the disk m

Parameter Data Formats4 - 18 C141-E167 BitByte765432100 000001001 X‘16’, X‘12’ or X‘0A’ (Page Length)2-4 Cylinder CountDefault X‘0

4.1 Mode ParametersC141-E167 4 - 19a. Cylinder countThis parameter specifies the total number of cylinders configured in the user space on the diskme

Parameter Data Formats4 - 20 C141-E167 BitByte765432100 000001111 X‘0A’ (Page Length)2 (Reserved) EER PER DTE DCRDefault00001000Vari

4.1 Mode ParametersC141-E167 4 - 21b. Number of retries during VERIFYThis parameter specifies the number of times reading of the disk media should be

Parameter Data Formats4 - 22 C141-E167 BitByte765432100 000010001 X‘0A’ or X‘12’ (Page Length)2 IC ABPF CAP DISC SIZE WCE MS RCDD

4.1 Mode ParametersC141-E167 4 - 23a. RCD (read cache disable)This bit can be specified, and its operation is as specified.This bit specifies whether

C141-E167FOR SAFE OPERATIONHandling of This ManualThis manual contains important information for using this product. Read thoroughly before usingthe

Command Processing1 - 2 C141-E167 BitByte765432100 Operation Code1 LUN 000002 Logical Block Address (MSB)3 Logical Block Address4 Logical Blo

Parameter Data Formats4 - 24 C141-E167d. SIZE (size enable) (not supported)"1" : Divides the data buffer in accordance with the value spe

4.1 Mode ParametersC141-E167 4 - 25"F" : Data put into the cache during a WRITE or WRITE and VERIFY command was notreplaced if there is o

Parameter Data Formats4 - 26 C141-E167"1" : Requests that the device server not read into the buffer any logical blocks beyond theaddressed

4.1 Mode ParametersC141-E167 4 - 27cache segments are occupied by data to be retained. If the number is at least one, cachingfunctions in the other se

Parameter Data Formats4 - 28 C141-E167a. TST (Task Set Type)This field specifies the type of task set defined below.Value Description000b Task set per

4.1 Mode ParametersC141-E167 4 - 29Despite the commands whose specified LBAs are overlapped, the IDD conducts reorderingoperation. Therefore the INIT

Parameter Data Formats4 - 30 C141-E167g. RAC (Report Check) (not supported)The IDD is not supported in this bit. Therefore, the IDD always report &qu

4.1 Mode ParametersC141-E167 4 - 314.1.8 Notch parameter (page code = 0C) BitByte765432100 000011001 X‘16’ (Page Lengt

Parameter Data Formats4 - 32 C141-E167If this parameter is issued, only the format parameter of the zone specified by the MODE SENSEcommand can be ref

4.1 Mode ParametersC141-E167 4 - 33• Starting BoundaryThis field is enabled by the MODE SENSE command. This field indicates the beginning of theact

1.1 Command FormatC141-E167 1 - 3(1) Operation codeBit 76543210Group Code Command CodeThe leading byte of all CDBs shows the format and type of comman

Parameter Data Formats4 - 34 C141-E167The log errors bit (LogErr) of zero indicates that the logging of informational exception conditionswithin a tar

4.1 Mode ParametersC141-E167 4 - 35MRIE DescriptorX’00’ No reporting of informational exception conditions:This method instructs the target to not re

Parameter Data Formats4 - 36 C141-E167The "Interval Timer" field indicates the period in 100 millisecond increments for reporting that aninf

4.2 Log ParametersC141-E167 4 - 37a. RPR (rounded parameter report)This bit stipulates the operation in the case where rounding up or rounding down p

Parameter Data Formats4 - 38 C141-E1674.2.1 Supprot log page (X'00')The supported log page returns the list of log pages implemented by the

4.2 Log ParametersC141-E167 4 - 394.2.2 Buffer overrun / underrun page (X'01') BitByte765432100000000011 X‘00’

Parameter Data Formats4 - 40 C141-E167• Data UnderrunCount of data underruns which occur during write operation when a buffer empty conditionprevents

4.2 Log ParametersC141-E167 4 - 414.2.3.2 Write errors recovered with possible delays (Page 02, Code 0001) BitByte7654321

Parameter Data Formats4 - 42 C141-E1674.2.3.4 Total posted recoverable write errors (Page 02, Code 0003) BitByte7654321045

4.2 Log ParametersC141-E167 4 - 434.2.3.6 Total posted unrecoverable write errors (Page 02, Code 0006) BitByte7654321045(

Command Processing1 - 4 C141-E167Furthermore, this field may be used with a different meaning, or it may not have any meaning at all,depending on the

Parameter Data Formats4 - 44 C141-E1674.2.4.1 Read errors recovered without delays (Page 03, Code 0000) BitByte7654321045(

4.2 Log ParametersC141-E167 4 - 454.2.4.3 Total posted read errors (Page 03, Code 0002) BitByte7654321045(MSB)X'0002

Parameter Data Formats4 - 46 C141-E1674.2.4.5 Total read bytes processed (Page 03, Code 0005) BitByte7654321045(MSB)X&apos

4.2 Log ParametersC141-E167 4 - 474.2.5 Verify error count page (X'05') BitByte765432100 000001011 X‘00’ (Reser

Parameter Data Formats4 - 48 C141-E1674.2.5.2 Vefiry errors recovered with possible delays (Page 05, Code 0001) BitByte765

4.2 Log ParametersC141-E167 4 - 494.2.5.4 Total posted recoverable verify errors (Page 05, Code 0003) BitByte7654321045(M

Parameter Data Formats4 - 50 C141-E1674.2.5.6 Total posted unrecoverable verify errors (Page 05, Code 0006) BitByte7654321

4.2 Log ParametersC141-E167 4 - 51The Counter Value indicates the count of all non-medium errors (01/xx/xx, 02/xx/xx, 04/xx/xx,05/xx/xx, 06/xx/xx, 07

Parameter Data Formats4 - 52 C141-E1674.2.7.2 Reference temperature (Page 0D, Code 0001) BitByte7654321045(MSB)X'0001

4.2 Log ParametersC141-E167 4 - 534.2.8.1 Date of manufacture (Page 0E, Code 0001) BitByte7654321045(MSB)X'0001&apos

1.1 Command FormatC141-E167 1 - 5Note:It is possible that bits 7 and 6 of the control byte will be used in future product specificationsas an inherent

Parameter Data Formats4 - 54 C141-E167The Accounting date specified by parameter code 0002h is a parameter that may be savable using aLOG SELECT comma

4.2 Log ParametersC141-E167 4 - 55The Accumulated start-stop cycles is a parameter provided by the device sever. The accumulatedstart-stop cycles pa

Parameter Data Formats4 - 56 C141-E167The values stored in the General usage parameter bytes represent data sent to the device server in aprevious LOG

4.2 Log ParametersC141-E167 4 - 574.2.11 SMART status page (X'2F')[Fujitsu unique page] BitByte765432100 001011

This page is intentionally left blank.

C141-E167 5 - 1CHAPTER 5 Sense Data Error Recovery Methods5.1 Sense Data5.2 INIT Error Recovery Methods (Recommended)5.3 Disk Drive Error Recovery P

Sense Data Error Recovery Methods5 - 2 C141-E167 BitByte765432100 Valid X ‘70’ or X ‘71’ (Error Code)1 X‘00’200ILI0 Sense Key3MSB45 Information

5.1 Sense DataC141-E167 5 - 3(2) Error codeThis field shows the format and type of sense data. The IDD always displays X ‘70’ (current error)or X ‘7

Sense Data Error Recovery Methods5 - 4 C141-E167(8) Sense code, sub-sense codeThe codes which indicate the reason for the error displayed by the sense

5.1 Sense DataC141-E167 5 - 5Table 5.1 Sense keySenseKeyName Explanation0 NO SENSE The specific sense key does not exist.1 RECOVEREDERROR1) Indicates

Command Processing1 - 6 C141-E1671.2 Status ByteFigure 1.4 shows status byte format and the type of status that the IDD supports.The status byte is on

Sense Data Error Recovery Methods5 - 6 C141-E167Table 5.2 Sense and subsense codes (1 of 5)C* Q* Name ExplanationSensekey00 No additional senseinforma

5.1 Sense DataC141-E167 5 - 7Table 5.2 Sense and subsense codes (2 of 5)C* Q* Name ExplanationSensekey13 00 Sync Byte not found forData fieldSB (Sync

Sense Data Error Recovery Methods5 - 8 C141-E167Table 5.2 Sense and subsense codes (3 of 5)C* Q*Name ExplanationSensekey1F 00 Partial Defect List Tran

5.1 Sense DataC141-E167 5 - 9Table 5.2 Sense and subsense codes (4 of 5)C* Q* Name Explanation Sensekey3D 00 Invalid bits in IDENTIFYmessage"1&

Sense Data Error Recovery Methods5 - 10 C141-E167Table 5.2 Sense and subsense codes (5 of 5)C* Q* Name ExplanationSensekey45 00 Select/Reselect failu

5.2 INIT Error Recovery Methods (Recommended)C141-E167 5 - 115.1.3 Sense data additional informationBytes 18 to 47 of sense data are defined as a Fuj

Sense Data Error Recovery Methods5 - 12 C141-E167ENDstatus received ?BUS FREEerror ?Timeout ?See item (3).See item (4).GOODBUSYQUEUEFULLYesYesYesYesNo

5.2 INIT Error Recovery Methods (Recommended)C141-E167 5 - 13(2) RESERVATION CONFLICT statusThis status shows, under a multi-initiator environment, t

Sense Data Error Recovery Methods5 - 14 C141-E167The cause of this error is the occurrence of an unrecoverable error on the SCSI bus, the occurrenceof

5.2 INIT Error Recovery Methods (Recommended)C141-E167 5 - 15Table 5.3 Sense data error classification (2 of 4)K* C* Q* Outline of Error L*Recovery

1.2 Status ByteC141-E167 1 - 7(2) CHECK CONDITION statusThis status is reported in the following cases a) to c). The IDD generates sense data when it

Sense Data Error Recovery Methods5 - 16 C141-E167Table 5.3 Sense data error classification (3 of 4)K* C* Q* Outline of Error L*Recovery Method(See Ta

5.2 INIT Error Recovery Methods (Recommended)C141-E167 5 - 17Table 5.3 Sense data error classification (4 of 4)K* C* Q* Error contents L*Recovery me

Sense Data Error Recovery Methods5 - 18 C141-E167Table 5.4 Error Recovery Processing Procedures (2 of 5)RecoveryMethodRecovery Processing Procedure5 1

5.2 INIT Error Recovery Methods (Recommended)C141-E167 5 - 19Table 5.4 Error recovery processing procedures (3 of 5)RecoverymethodRecovery processin

Sense Data Error Recovery Methods5 - 20 C141-E167Table 5.4 Error recovery processing procedures (4 of 5)RecoverymethodRecovery processing procedure18

5.2 INIT Error Recovery Methods (Recommended)C141-E167 5 - 21Table 5.4 Error recovery processing procedures (5 of 5)RecoverymethodRecovery processin

Sense Data Error Recovery Methods5 - 22 C141-E1675.3 Disk Drive Error Recovery ProcessingThis section explains concerning error recovery processing me

5.3 Disk Drive Error Recovery ProcessingC141-E167 5 - 23If error correction is permitted but immediate correction is not permitted (DCR = 0, EER = 0)

Sense Data Error Recovery Methods5 - 24 C141-E167Remark:1. When this function is specified (ARRE = "1"), the EER flag's specification i

5.3 Disk Drive Error Recovery ProcessingC141-E167 5 - 25Sectors to be made AWRE shall be following:• the sector where the error occurs and the latte

Command Processing1 - 8 C141-E167 (6) INTERMEDIATE CONDITION MET StatusThis status is reported when it is possible to secure the cache memory area nec

Sense Data Error Recovery Methods5 - 26 C141-E167b. Verify Error Recovery Parameters (Page Code = 7)• EER (enable early recovery)• PER (post error)•

C141-E1676 - 1CHAPTER 6 Disk Media Management6.1 Defect Management6.2 Disk Media Initialization6.3 Data Block Verification Methods (Recommended)6.4

Disk Media Management6 - 2C141-E167(2) Alternate block allocationAlternate data blocks are allocated in defective sector units for defective data bloc

6.2 Disk Media InitializationC141-E167 6 - 3• Alternate block allocation processing during FORMAT UNIT command executionWith the FORMAT UNIT command,

Disk Media Management6 - 4C141-E167(1) Issuing the MODE SELECT commandThe MODE SELECT or MODE SELECT EXTENDED command is issued and the format attribu

6.2 Disk Media InitializationC141-E167 6 - 56.2.2 Re-initializationThe INIT can reinitialize the disk drive after it has been operated using the FORM

Disk Media Management6 - 6C141-E1676.3 Data Block Verification Methods (Recommended)The recommended procedure for verifying from the INIT the normalcy

6.4 Alternate Block Allocation ProcessingC141-E167 6 - 7(3) Reading and verification of dataIssue the READ, READ EXTENDED or VERIFY command and verif

Disk Media Management6 - 8C141-E167The alternate block allocation history (defect position information) is registered as an addition to thedefect list

C141-E167 GL-1GlossaryAxial accelerationAcceleration in the recording layer along the line perpendicular to the diskreference surface at a specified r

1.3 Outline of Command ProcessingC141-E167 1 - 96) When execution of the command is completed, the TARG reports the execution results by thestatus byt

GlossaryGL-2 C141-E167Initiator (INIT)This is a SCSI device which initiates input and output operations on the SCSI bus.In this manual, initiator has

GlossaryC141-E167 GL-3status, this is information generated by the target for reporting detailedinformation on that status.Sense KeyThis is a 4-bit co

This page is intentionally left blank.

C141-E167 AB-1Acronyms and AbbreviationsAACK AcknowledgeATN AttentionAWG American Wire GaugeBBSY BusyCC/D Control/dataCCS Common command setCDB Common

This page is intentionally left blank.

Comments concerning this manual can be directed to one of the following addresses:FUJITSU LIMITEDBusiness PlanningSolid Square East Tower580 Horikawa-

This page is intentionally left blank.

C141-E167 IN-1Index10-byte CDB basic format 1-212-byte CDB basic format 1-26-byte CDB basic format 1-1Aaccounting date 4-53ACE 3-18active no

IndexIN-2 C141-E167changing reserve condition 3-39CHECK CONDITION status 1-7C list 3-76, 6-1clocking field 3-8CmdDt 3-3commandsupport data

IndexC141-E167 IN-3disconnect processing 1-11, 1-12exception 1-14procedure after COMMAND phaseexecution 1-13procedure after data transferexecuti

Command Processing1 - 10 C141-E167Table 1.1 Responses to Link Specification CommandsFlag End Status Status Message Link Function0CompletedNormallyINTE

IndexIN-4 C141-E167Hhandling illegal CDB 1-5hard sectoring 4-17header 3-16, 3-22, 3-32, 3-78, 3-89header + datawith address specification 3-10

IndexC141-E167 IN-5mode=0, 0, 1, 1 3-109mode=0, 1, 0, 0 3-104mode=0, 1, 0, 1 3-105mode=0, 1, 1, 0 3-105mode=0, 1, 1, 1 3-106mode=1, 0, 1, 0

IndexIN-6 C141-E167parameter specification 3-94parameter specifyingsector format 4-16track format 4-15PER 4-4, 4-20Perf 4-34persistent reser

IndexC141-E167 IN-7object and third party releasefunction 3-41RELEASE EXTENDED 3-42removable medium 4-17report check 4-30REPORT DEVICE IDENTIF

IndexIN-8 C141-E167spindle motor start delay time 3-18SSEC 4-16standard INQUIRY data 3-3, 3-4starting boundary 4-33start specification 3-37s

IndexC141-E167 IN-9WP bit 3-32WRITE 3-67WRITE AND VERIFY 3-69, 4-20WRITE BUFFER 3-102command 3-103write cache 2-10enable 4-23write error

This page is intentionally left blank.

READER’S COMMENT FORMYour comments or suggestions on this document are cordially solicited. For any comments and suggestionsyou may have, please comp

This page is intentionally left blank.

1.3 Outline of Command ProcessingC141-E167 1 - 111.3.3 Disconnect/reconnect processingWhen processing is performed by the TARG during the command exec

C141-E167Revision History(1/1)Edition DateRevised section (*1)(Added/Deleted/Altered)Details01 May, 2002 — —*1 Section(s) with asterisk (*) refer to t

Command Processing1 - 12 C141-E167Table 1.2 Types of Command and Disconnect ProcessingCommands with executing disconnect processing. (Note 2)

1.3 Outline of Command ProcessingC141-E167 1 - 13(2) Basic disconnect processing procedureDisconnect processing is executed basically by the following

Command Processing1 - 14 C141-E167Note:In disconnect processing in this case, transfer of all the data accompanying execution of thecommand is complet

1.3 Outline of Command ProcessingC141-E167 1 - 153) After the INIT that accepts the IDENTIFY message normally completes the pointerrestore operation,

Command Processing1 - 16 C141-E167The IDD maintains data transfer mode settings between itself and each INIT individually. Therefore,an INIT which us

1.4 Command Queuing FunctionC141-E167 1 - 17When a command is in the queued state, if a RESET condition occurs, or if the IDD receives aTARGET RESET m

Command Processing1 - 18 C141-E167a) When there is an error in the CDB, the IDD responds with a CHECK CONDITIONstatus at the point when that command

1.5 UNIT ATTENTION ConditionC141-E167 1 - 19The INIT can specify 2 error recovery options by the QErr bit of the control mode parameter (PageA) of the

Command Processing1 - 20 C141-E167(1) When power on, RESET or TARGET RESET occursIf the IDD’s power is switched on, the IDD enters the RESET condition

1.5 UNIT ATTENTION ConditionC141-E167 1 - 21• Power on [=29-01]• Reset [=29-02]• TARGET RESET [=29-03]• Transciever Mode Changed to SINGLE-ENDED [=29-

This page is intentionally left blank.

Command Processing1 - 22 C141-E167The IDD executes the REQUEST SENSE command normally and sends the sense data whichindicate the UNIT ATTENTION condit

1.7 Command Processing ExceptionsC141-E167 1 - 231) If a command is issued to the logical unit in the sense data hold state by the INIT which is theob

Command Processing1 - 24 C141-E1672) The IDD reports a CHECK CONDITION status for a command that generates an overlap. Atthis time, the sense data ge

1.7 Command Processing ExceptionsC141-E167 1 - 25• When reading of system information is not completed, or reading failed.Also, if initialization of

Command Processing1 - 26 C141-E167reached the normal rotating speed, or if reading of system information is still in progress, a CHECKCONDITION status

1.7 Command Processing ExceptionsC141-E167 1 - 27Table 1.4 Outline of SCSI Bus Error Recovery ProcessingItem Type of Error Error Recovery Processing1

Command Processing1 - 28 C141-E1671.7.6 Reset processingThe INIT can reset the SCSI bus with following.• RESET condition• TARGET RESET message• CLE

1.7 Command Processing ExceptionsC141-E167 1 - 29Table 1.6 Reset processing during writeType of command Halting process of command executionWRITEWRITE

Command Processing1 - 30 C141-E167After this state occurs, the IDD reports the CHECK CONDITION status for all input/outputoperation requests except th

1.8 Data Block AddressingC141-E167 1 - 31MAP3147 MAP3735 MAP3367 MAS3367 MAS3735z73 TBDa14 TBDb1 TBDc 1044 TBD TBDd 48970 49040 49166 TBD TBDm8 4 2 TB

C141-E167iPrefaceThis manual explains concerning the MAS3367, MAS3735, MAP3367, MAP3735,MAP3147 series 3.5 inch hard disk drives with internal SCSI co

Command Processing1 - 32 C141-E1671.8.2 Logical block addressingThe IDD uses logical data block addressing which is not dependent on the disk drive’s

C141-E167 2 - 1CHAPTER 2 Data Buffer Management2.1 Data Buffer2.2 Look-Ahead Cache Feature2.3 Write CacheIn this chapter, the configuration of the dat

Data Buffer Management2 - 2 C141-E167Segment 7Segment 6Segment 5Segment 4←Read←ReadWrite→Segment 3Segment 2Segment 1Segment 0Valid DataWrite→Disk Medi

2.1 Data BufferC141-E167 2 - 36) When transfer of all the specified data is completed, the IDD reports the status and terminatesthe command.Note:In or

Data Buffer Management2 - 4 C141-E1673) If the data transfer rate of the INIT (SCSI bus) is lower than the data transfer rate of the disk drive,since

2.1 Data BufferC141-E167 2 - 52.1.2 Operation mode setting(1) MODE SELECT parameterIn order to make it possible to control from the INIT the reconnect

Data Buffer Management2 - 6 C141-E167b. Buffer empty ratioThis parameter specifies the timing for the IDD to start reconnection when it is requested b

2.2 Look-Ahead Cache FeatureC141-E167 2 - 7(1) Caching object commandsCommands which execute caching operations are the commands shown below:• READ• R

Data Buffer Management2 - 8 C141-E167b) If any of the following commands is issued, all the data which are objects of caching aredisabled.•CHANGE DEFI

2.2 Look-Ahead Cache FeatureC141-E167 2 - 92.2.2 Caching parametersThe IDD supports the MODE SELECT parameters (caching parameters: page code = 8) sho

Prefaceii C141-E167GlossaryThe glossary explains technical terms which are necessary to the reader's understandingwhen reading this manual.List o

Data Buffer Management2 - 10 C141-E1672.2.3 Look-Ahead operation, Look-Ahead volume1) Excluding the conditions in 3) and 4) for the amount of data spe

2.3 Write CacheC141-E167 2 - 112.3 Write CacheThe IDD is equipped with a write cache function in order to reduce the INIT's command processingtim

This page is intentionally left blank.

C141-E167 3 - 1CHAPTER 3 Command Specifications3.1 Control/Sense Commands3.2 Data Access Commands3.3 Format Commands3.4 Maintenance, Diagnostic Comma

Command Specifications3 - 2 C141-E1673.1.2 INQUIRY (12) BitByte765432100 X‘12’1 LUN 0 0 0 CmdDt EVPD2 Page Code/Operation Cpde3000000004 Tran

3.1 Control/Sense CommandsC141-E167 3 - 3(1) EVPD (Enable Vital Product Data)a) If the specification in this bits is zero, the IDD transfers the stan

Command Specifications3 - 4 C141-E167 BitByte76 5 4 3 2 10SCSI modeQualifier Device Type Code0(0, 0, 0) or (0, 1, 1) (0, 0, 0, 0, 0) or (1

3.1 Control/Sense CommandsC141-E167 3 - 5a. Qualifier field(0,0,0): The specified logical unit shows the type of input/output device shown in the &qu

Command Specifications3 - 6 C141-E167g. Supported functionsThe bit positions shown below are valid only when the CHANGE DEFINITION command is setso th

3.1 Control/Sense CommandsC141-E167 3 - 7• SCSI-2 mode[Byte 3]- AENC (Asynchronous event notification capability):Asynchronous condition notify funct

PrefaceC141-E167 iiiCONVENTIONS USED INTHIS MANUALNote 1: Model NameMAP3367 NCInterface type NP: Low voltage differential 16-bit SCSI Ultra-320NC: Low

Command Specifications3 - 8 C141-E167k. Device Serial Number fieldThe value following byte 4 of the device serial number in the VPD information is ind

3.1 Control/Sense CommandsC141-E167 3 - 9(6) Command Support DataFigure 3.2 shows the format and contents of the command support data transferred to

Command Specifications3 - 10 C141-E167media. When this is the case, a subsequent request for command support data may besuccessful.c. CDB sizeThis f

3.1 Control/Sense CommandsC141-E167 3 - 11 BitByte765432100 Qualifier Device Type Code1 X‘00’ (Page Code)2 X‘00’3 X‘03’ (Page Length)4 X‘00’

Command Specifications3 - 12 C141-E167The values indicated in the "Qualifier" and "Device Type Code" fields in byte 0 are the same

3.1 Control/Sense CommandsC141-E167 3 - 133.1.3 READ CAPACITY (25) BitByte765432100 X‘25’1 LUN 000002 Logical Block Address (MSB)3 Logical B

Command Specifications3 - 14 C141-E167 BitByte765432100 Logical Block Address (MSB)1 Logical Block Address2 Logical Block Address3 Logical Bl

3.1 Control/Sense CommandsC141-E167 3 - 15This command specifies a different SCSI level in the "SCSI level" field in SCB byte 3. The SCSIl

Command Specifications3 - 16 C141-E167 BitByte765432100 X‘00’1 X‘00’2 X‘00’3 X‘04’ (Parameter Length)4000WDTRUNTAINSDTR RSRTY 05 PHSCRC AGD AC

3.1 Control/Sense CommandsC141-E167 3 - 17* Set at shipping timeb) UNTATN (UNIT ATTENTION report mode)This specifies the response method to command

Prefaceiv C141-E167Related StandardsSpecifications and functions of products covered by this manual comply with the followingstandards.Standard (Text)

Command Specifications3 - 18 C141-E167* Set at shipping time The IDD ignores this specification and operates with the settings specified at

3.1 Control/Sense CommandsC141-E167 3 - 193.1.5 MODE SELECT (15) BitByte765432100 X‘15’1 LUN PF 0 0 0 SP2000000003000000004 Parameter List L

Command Specifications3 - 20 C141-E167If a "Header," "Block Descriptor" or any "Page Descriptor" cannot be transferred w

3.1 Control/Sense CommandsC141-E167 3 - 21Block descriptorPages: 3, 4RemarkWhen the drive is shipped from the factory,there are not parameter page “S

Command Specifications3 - 22 C141-E167If the IDD performs rounding processing ("rounding up" or "rounding down") of parameter valu

3.1 Control/Sense CommandsC141-E167 3 - 23Page Descriptor BitByte765432100 0 0 Page Code1 Page Length2nFigure 3.8 MODE SELECT command (Group

Command Specifications3 - 24 C141-E167If only the "Block descriptor" in this command is changed, the IDD changes the values inthe "Sect

3.1 Control/Sense CommandsC141-E167 3 - 25c. Page descriptorThe "Page descriptor" is configured from a 2-byte page header followed by a par

Command Specifications3 - 26 C141-E1672. After changing anything in the "Block descriptor," "Format parameters (Page 3)" or "

3.1 Control/Sense CommandsC141-E167 3 - 27Figure 3.9 shows the configuration of the parameter list (MODE SELECT parameters)transferred by this command

C141-E167 vProduct/Maintenance Manual1. General Description2. Specifications3. Data Format4. Installation Requirements5. Installation6. Diagnostics

Command Specifications3 - 28 C141-E167Page DescriptorBitByte765432100 0 0 Page Code1 Page Length2nFigure 3.9 MODE SELECT EXTENDED command (Group 2) pa

3.1 Control/Sense CommandsC141-E167 3 - 29Page Code Page Descriptor Name CCS SCSI-2 SCSI-31 Read/Write Error Recovery Parameter 8 bytes 12 bytes 12 b

Command Specifications3 - 30 C141-E167Table 3.1 MODE SENSE Data Type SpecificationsPC Type of Parameter Transferred to the INIT00 Current Values:Repor

3.1 Control/Sense CommandsC141-E167 3 - 31HeaderBitByte765432100 Sense Data Length1 X‘00’ (Media Type)2 WP 0 0 DPOFUA 0 0 0 03 X‘00’ or X‘08’ (Block D

Command Specifications3 - 32 C141-E167(1) Headera. Sense data lengthThis field indicates the length (number of bytes) of the parameter list (MODE SENS

3.1 Control/Sense CommandsC141-E167 3 - 33Furthermore, when this command specifies to transfer the "Default" value and "Variable"

Command Specifications3 - 34 C141-E1673.1.8 MODE SENSE EXTENDED (5A)BitByte765432100X‘5A’1LUN0DBD0002 PC Page Code3 000000004 000000005 000000006 0000

3.1 Control/Sense CommandsC141-E167 3 - 35Block DescriptorBitByte765432100 Data Block Count (MSB)1 Data Block Count2 Data Block Count3 Data Block Coun

Command Specifications3 - 36 C141-E167This command moves the read/write heads of the disk drive to the initial position. A data block withthe logical

3.1 Control/Sense CommandsC141-E167 3 - 37Depending on the value specified in the "Immed (immediate)" bit, bit 0 of CDB byte 1, the timing