Fujitsu SPARC ENTERPRISE M8000 Manual de usuario Pagina 341
- Pagina / 514
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 18 AC Section Replacement 18-5
18.2 Cold Replacement
In cold replacement, none of the replacement work is performed with the
maintenance menu from a terminal connected to XSCF.
The procedure is as follows.
1. Unlock and open a door of the server.
For details, see Chapter 5.
2. Change the mode switch setting on the operator panel from Locked to Service.
Note – When the maintenance work is completed, be sure to confirm the mode
switch setting and return the switch to Locked.
3. Stop (turn off power) all domains together. Take either of the following two
actions:
■ Press and hold the POWER switch on the operator panel for at least four
seconds.
■ From a console that is connected to XSCF, log in to XSCF, and execute the
poweroff -a command.
The OS shutdown processing is executed for all the domains, and then the
power-off processing is executed.
4. Confirm that the power-off processing is completed by confirming that the
POWER LED (green) on the operator panel is off.
5. Switch off all main line switches for the AC section (ACS) in the power supply
system.
For details, see Section 4.5.3, “Main Line Switch Locations” on page 4-28.
Note – If the optional three-phase 200 VAC input power supply unit is installed, the
main line switches are located on the three-phase ACS.
Caution – If the dual power feed option is installed, switch off the main line
switches for both power supply units.
- SPARC Enterprise 3
- M8000/M9000 Servers 3
- Service Manual 3
- Contents 7
- Contents vii 9
- Contents ix 11
- Contents xi 13
- Contents xiii 15
- Contents xv 17
- Glossary 19
- Preface xix 21
- SPARC Enterprise M8000/M9000 23
- Servers Documentation 23
- Book Titles Manual Codes 24
- Preface xxiii 25
- Product Handling 26
- Preface xxv 27
- Limitations and Cautions 28
- Preface xxvii 29
- Troubleshooting 31
- Safety and Tools 33
- 1.1.2 Prompt Notations 34
- 1.2 Precautions 36
- Maintenance Tools 37
- Product Overview and 39
- FIGURE 2-3, FIGURE 2-6 40
- FIGURE 2-1 Front View - M8000 41
- Rear View - M8000 42
- Air Filter 42
- 2.2 Labels 49
- ID label (Japan) 50
- EZ label (besides Japan) 50
- M8000 Label Location 51
- Standard label 51
- System Name Plate Label 51
- M9000 Label Location 52
- 2.2.2 Labels About Handling 53
- 2.3 Operator Panel 54
- 2.3.3 LED 56
- 2.3.4 Switch 58
- Methods To Use 59
- Configuration 61
- Configurations 62
- Command Description 63
- XSCF> version 64
- ■ Diagnoses the problems 65
- 2.6.2 Monitoring Output 66
- 2.6.3 Messaging Output 67
- 2.7 LED Error Display 68
- LED Display and meaning 69
- MeaningType Display 71
- 2.8.3 Using the fmadm Command 73
- 2.8.3.2 fmadm faulty Command 74
- 2.8.3.3 fmadm repair Command 74
- Commands 75
- 2.9.1 iostat Command 76
- 2.9.2 prtdiag Command 77
- 2.9.3 prtconf Command 82
- 2.9.3.1 Options 83
- 2.9.4 netstat Command 84
- 2.9.5 ping Command 85
- 2.9.5.1 Options 86
- 2.9.6 ps Command 87
- 2.9.7 prstat Command 88
- Periodic Maintenance 89
- Removal of Air Filters 92
- Fixing bracket (x3) 93
- FRU Removal Preparation 95
- 4.1.1 FRU Replacement 96
- 4.2 Active Replacement 97
- 4.2.3.1 Configuring CMU/IOU 100
- 4.2.4 Confirming the Hardware 101
- Manual, or the man page 102
- 4.3 Hot Replacement 106
- 4.3.2 Confirming the Hardware 109
- 4.4 Cold Replacement 112
- 4.4.2 Powering the Server On 113
- 4.4.3 Confirming the Hardware 114
- 4.5.1 Types of Power Supply 118
- 4.5.1.1 AC Input Power 119
- 4.5.1.2 Power System 121
- 4.5.2.1 Power-On 122
- 4.5.2.2 Power-Off 122
- -Main line switch (x3) 123
- Power Feed 124
- -Main line switch (x5) 126
- 4.6 Emergency Switch-Off 129
- M8000 Server 129
- Cable Routing Procedure 132
- Hook-and-loop Fasteners Used 132
- FIGURE 4-12.) 134
- FIGURE 4-14.) 137
- FIGURE 4-15.) 138
- (M8000, rear view) 139
- Ventilation 141
- FIGURE 4-18.) 142
- FIGURE 4-18 142
- FIGURE 4-19 142
- FIGURE 4-19.) 142
- II Maintenance 145
- Internal Components Access 147
- That Can Be Accessed 148
- 5.3 How to Remove a Door 149
- Operator panel 150
- Cable holder 150
- Sensor unit 150
- How to Remove a Side Panel 151
- Replacement of CPU/Memory 153
- M8000 CMU#0 to 3 156
- M9000 base cabinet CMU#0 to 7 156
- 6.2 CPU Upgrade 157
- XSCF> poweron -d domain_id 159
- XSCF> showlogs power 159
- XSCF> showlogs error -v 159
- XSCF> showstatus 159
- With SPARC64 VI 162
- Existing Domain 163
- Replacement 164
- ■ Active replacement: 166
- ■ Hot replacement: 166
- FIGURE 6-7) 169
- CPU and DIMM Locations 171
- CPU (x4) 171
- DIMM (x32) 171
- Duct cover 171
- 6.4 Cold Replacement 173
- FIGURE 6-5 or FIGURE 6-6) 174
- 6.5 CPU and DIMM Replacement 177
- 6.5.1 Replacing a CPU Module 179
- 1. Remove the CPU Module 180
- CMU Guide Lock (Enlarged) 181
- Lever Up the CPU Module 182
- Remove the CPU Module 183
- Mounting the CPU Module 189
- 6.5.3 DIMM Replacement 193
- Notch of DIMM 194
- I/O Unit (IOU) Replacement 195
- 7.1 Overview of the IOU 196
- M8000 IOU#0 to 3 201
- IOU#1, 3, 5, and 7 (rear) 201
- IOU#9, 11, 13, and 15 (rear) 201
- 7.3 Cold Replacement 210
- FIGURE 7-7 - FIGURE 7-9) 211
- FAN Unit Replacement 215
- 8.1 Overview of the FAN Unit 216
- FAN_A#0-#3 218
- 8.3 Cold Replacement 227
- FIGURE 8-11) 228
- Power Supply Unit (PSU) 231
- Power cabinet 233
- M8000 PSU#0 to 8 PSU#10 to 19 237
- 9.3 Cold Replacement 241
- FIGURE 9-8 or 242
- FIGURE 9-9) 242
- Operator Panel Replacement 245
- 10.2 Cold Replacement 248
- Removing the OPNL 250
- XSCF Unit Replacement 253
- XSCFU_B#1 254
- XSCFU_B#0 254
- M8000 XSCFU_B#0, 1 256
- XSCF> unlockmaintenance 262
- 11.3 Cold Replacement 263
- FIGURE 11-5 or FIGURE 11-6) 264
- Hard Disk Drive (HDD) 267
- 12.2 Active Replacement 268
- Removing the HDD 270
- 12.3 Cold Replacement 271
- FIGURE 12-2) 272
- PCI Slot Device Replacement 275
- ■ Link card 276
- 13.2 Active Replacement 277
- Removing the PCI Cassette 279
- Pushing In the Lever 280
- Lock bracket 280
- Loosening Screws of Latches 281
- Removing the PCI Card 282
- 1 Card positioning post 283
- 2 Card positioning tab 283
- Mounting the PCI Card 284
- FIGURE 13-9 reference) 286
- Tightening the Screw 287
- Reinserting the Lever 288
- 13.3 Hot Replacement 290
- FIGURE 13-11) 292
- 13.4 Cold Replacement 293
- FIGURE 13-3) 294
- FIGURE 13-4) 294
- FIGURE 13-5) 294
- FIGURE 13-9) 295
- CD-RW/DVD-RW Drive Unit 297
- Cabinet) 299
- 14.2 Active Replacement 300
- # cfgadm -a 301
- 14.3 Hot Replacement 305
- FIGURE 14-4 or 306
- FIGURE 14-5) 306
- 14.4 Cold Replacement 307
- Tape Drive Unit Replacement 309
- Tape drive unit TAPEU 312
- 15.2 Active Replacement 313
- 15.3 Hot Replacement 317
- 15.4 Cold Replacement 318
- FIGURE 15-4 or FIGURE 15-5) 319
- 16.1 Overview of the CLKU 321
- CLKU_B#0 322
- CLKU_B#1 322
- 16.2 Cold Replacement 323
- FIGURE 16-3) 324
- Crossbar Unit Replacement 329
- 17.2 Cold Replacement 331
- FIGURE 17-3) 332
- AC Section Replacement 337
- 18.2 Cold Replacement 341
- FIGURE 18-4): 342
- FIGURE 18-5): 342
- FIGURE 18-6) 342
- DDC Replacement 347
- M8000 DDC_A#0, 1 348
- 19.3 Cold Replacement 352
- FIGURE 19-3) 353
- Backplane Replacement 357
- 20.2.1 M8000/M9000 BPs 358
- For details, see Chapter 5 360
- FIGURE 20-6): 362
- FIGURE 20-4): 362
- FIGURE 20-7): 363
- FIGURE 20-5): 363
- 20.2.2 PSU BP 370
- PSUBP_A#0 371
- PSUBP_A#1 371
- PSUBP_A#2 371
- FIGURE 20-11): 373
- FIGURE 20-12): 374
- 20.2.3 FAN BP 377
- FANBP_C#1 378
- FANBP_C#0 378
- Front Rear 378
- Sensor Unit Replacement 387
- 21.2 Cold Replacement 390
- FIGURE 21-4 or FIGURE 21-5) 391
- Media Backplane Replacement 395
- M8000 MEDBP 398
- 22.2 Cold Replacement 399
- FIGURE 22-4): 400
- FIGURE 22-5): 400
- Switch Backplane Replacement 405
- M8000 SWBP 408
- 23.2 Cold Replacement 409
- FIGURE 23-4): 410
- FIGURE 23-5): 410
- FIGURE 23-4 or FIGURE 23-5) 410
- Expansion Cabinet 415
- 24.1 Addition and Deletion of 416
- 24.1.2 Addition and Deletion 417
- 24.1.2.2 Deletion 426
- M8000 + Power Cabinet 427
- M9000 expansion cabinet 430
- Addition and Deletion of CMU 431
- DIMM, IOU, HDD, PCI Cards and 431
- 25.1 Addition 432
- 25.1.2 Cold Addition 433
- 25.2 Deletion 434
- 25.2.1 Active Deletion 435
- 25.2.2 Cold Deletion 435
- XSCF> showhardconf 436
- System Configuration 437
- A.2 System Configuration 438
- Expansion Cabinet) 442
- AC section) 445
- Components 447
- Appendix B Components B-3 449
- B.1 CPU Memory Board Unit 450
- B.2 CPU Module 451
- B.3 Memory 453
- B.4 I/O Unit 454
- Appendix B Components B-9 455
- B.5 Hard Disk Drive 456
- B.6 PCI Cassette 456
- Appendix B Components B-11 457
- FIGURE B-6 shows the PCICS 457
- B.7 IOU Onboard Device Card 458
- Connection Card) 459
- B.9 Crossbar Unit 460
- Appendix B Components B-15 461
- B.10 Clock Control Unit 462
- B.11 XSCF Unit 463
- B.12 CD-RW/DVD-RW Drive Unit 465
- B.13 Tape Drive Unit 466
- B.14 Operator Panel 467
- B.15 Sensor Unit 469
- B.16 Power Supply Unit 470
- B.17 AC Section 471
- AC Section (ACS_B) 472
- AC Section (ACS_C) 472
- AC Section (ACSTPH_A) 473
- AC Section (ACSTPH_B) 473
- AC power to 30 PSUs 474
- AC Section (ACS_D) 475
- B.18 FAN Unit 476
- FAN Unit (FAN_B) 477
- B.19 Power Cabinet 478
- Power Cabinet 479
- FIGURE B-30 480
- B.21 Backplane 481
- Backplane (BP_B) 482
- B.22 DDC 483
- B.23 PSU Backplane 484
- B.24 FAN Backplane 485
- FAN Backplane (FANBP_B) 486
- FAN Backplane (FANBP_C) 486
- Appendix B Components B-41 487
- B.25 Media Backplane 488
- B.26 Switch Backplane 489
- C.1 Serial Port 491
- C.2 UPC Port 492
- C.3 USB Port 492
- UPS Controller 495
- Appendix D UPS Controller D-3 497
- D.4 Power Supply Conditions 498
- D.5 UPS Cable 499
- D.6 Connections 500
- D.7 UPC Port 501
- 1040 or 1041 Is in the Server 503
- Abbreviations 507
Relacionado con productos y manuales para Ordenadores Fujitsu SPARC ENTERPRISE M8000
Ordenadores Fujitsu PRIMERGY RX600 S5 Manual de usuario
(148 paginas)
(148 paginas)
Ordenadores Fujitsu PRIMERGY RX900 S1 Manual de usuario
(368 paginas)
(368 paginas)
Ordenadores Fujitsu FR family 32-bit microcontroller instruction manue Manual de usuario
(314 paginas)
(314 paginas)
Ordenadores Fujitsu V810 Manual de usuario
(76 paginas)
(76 paginas)
Ordenadores Fujitsu ServerView Resource Orchestrator Cloud Edition V3. Manual de usuario
(180 paginas)
(180 paginas)
Ordenadores Fujitsu M8000 Manual de usuario
(518 paginas)
(518 paginas)
Ordenadores Fujitsu SPARC M4000 Manual de usuario
(376 paginas)
(376 paginas)
Ordenadores Fujitsu C120-E361-04EN Manual de usuario
(36 paginas)
(36 paginas)
Ordenadores Fujitsu SPARC M3000 Manual de usuario
(56 paginas)
(56 paginas)
Ordenadores Fujitsu T2000 Manual de usuario
(30 paginas)
(30 paginas)
Ordenadores Fujitsu Primergy ServerView Suite ServerView Remote Manage Manual de usuario
(62 paginas)
(62 paginas)
Ordenadores Fujitsu T1000 Manual de usuario
(84 paginas)
(84 paginas)
Ordenadores Fujitsu BS2000 Manual de usuario
(37 paginas)
(37 paginas)
Ordenadores Fujitsu Primergy RX200 S2 Manual de usuario
(307 paginas)
(307 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales